Se rendre au contenu

E3D

Enhance your printing experience with the Starlex DHB hot-end, featuring exceptional thermal efficiency and a flow rate starting at 22.5mm3/s. It mirrors the capabilities of the Volcano nozzle without compromising Z height.

Most of the items below would fit E3D products. Original V6 as well as Revo standard.

Kit complet, Starlex DHB 2.5x22.5 HSS E3D V6 HS Replacement standard + 2x MCH 30W 24V Microfit 3.0 + Harness
Contient:
1x E3D Groove HS adapted height for DHB 22.5
1x Base set M7 (BP D7x22; HSC M7x10; Spring In)
1x Starlex DHB D2.5x22.5 Hot-end set
2x MCH Heater 30W, 24V Microfit 3.0
1x Harness Microfit 3.0

+ selected items

PAS Inclu:
1x connecteur pour Thermistor JST GH 1.25 / XH 1.25
Bowden tube

ILes images ne sont pas contractuelles
107.30 CHF 107.3 CHF
18.90 CHF 18.9 CHF
HS E3D V6 Groove Dissipateur thermique adapté (DHB22.5)
Pour une extrémité chaude de remplacement standard, même hauteur avec le DHB 22.5
17.90 CHF 17.9 CHF
HSCS D4 D6 tube Spacer
Brass tube spacer
3.50 CHF 3.5 CHF
Base Plate D4 Rounded
Rectangular Rounded Edges Stainless Steel Base Plate D4, Voron, Revo
5.90 CHF 5.9 CHF
Base Plate D7-L D22
Round Stainless Steel Base Plate D7 Lock OD 22mm
7.90 CHF 7.9 CHF
HSC for E3D M4 Revo/Hemera
Heat Sink Connector pour E3D M4 systems
11.40 CHF 11.4 CHF
HSC M7 x 10 L
Hex 7mm
8.90 CHF 8.9 CHF
HSC M7 x 15
Hex 7mm
7.90 CHF 7.9 CHF
Base Plate Set M4 Revo + Spacer + Spring In
Revo M4 HSC Base Plate D4 Rounded & Tube Spacer
21.90 CHF 21.9 CHF
Base Plate Set M7S x 15 + Spacer + Spring In
M7S = Base plate D7 + HSC thread M7 + Spacer HSCS D7 + Spring
21.90 CHF 21.9 CHF
Base Plate Set M7S for E3D V6 Original HS + Spacer + Spring In
This Base Set will fit into an original V6 Heat Sink.
It will increase 7mm the Nozzle height, fan shroud will need to be adapted.
The electrical wiring will need to be adapted to support the 2x30W MCH heaters and the Thermistor (NTC 100K 3950 - JST gh1.25).
21.90 CHF 21.9 CHF
Base Plate Set Round M7S x 10 + Spacer + Spring In
M7S = Base plate D7R22 + HSC thread M7x10 + Spacer HSCS D7 + Spring In
21.90 CHF 21.9 CHF
Base Plate Set M7 + E3D V6 Adapted M12 HS + Spring In
Replacement hot-end, same height with DHB 22.5 only
39.90 CHF 39.9 CHF
Base Plate Set M7 + E3D V6 Adapted Groove HS (DHB22.5) + Spring In Cold Set
This Cold set is a drop in replacement, to keep same Nozzle height with DHB 22.5 only, any other Hot-end can also be mounted, increasing Z height and flow performance.
It includes: Groove V6 modified HS, HSC M7 (K), Base plate D7L (M), Spring in.
Pre-mounted
39.90 CHF 39.9 CHF
Starlex DHB D2.5x22.5 Hot-end Base Set Only
For Hardened Stainless Steel Nozzle D2.5x22.5
87.90 CHF 87.9 CHF
Starlex DHB D2.5x24 Hot-end Set de Base Uniquement
Contient:
2x HB 2.5x24;
2x HB 24 Clamp;
1x Clip 2.5;
1x Sock;


NON COMPRIS : Buse, résistances HSC, HSCS, MCH, Thermistance, Plaque de base...

Les images ne sont pas contractuelles
90.90 CHF 90.9 CHF
Starlex DHB D3.0x22.5 Hot-end Base Set Only
Content:
2x HB 3x22.5;
2x HB 22.5 Clamp;
1x Clip 3;
1x Sock;

NOT INCLUDED: Nozzle, HSC, HSCS, MCH heaters, Thermistor, Base Plate...
Images are not contractual
87.90 CHF 87.9 CHF
Toutes les pièces conçues par Swiss3Dc sont fabriquées et produites en Suisse, les pièces standard peuvent être importées.

Les couleurs des pièces figurant sur les images du magasin et du site Internet sont données à titre indicatif.

AVERTISSEMENT ⚠️ : Certains produits vendus sur ce site web peuvent vous exposer à des produits chimiques, notamment les huiles minérales, dont l'État de Californie sait qu'elles sont susceptibles de provoquer le cancer, ainsi que le plomb et le nickel, dont l'État de Californie sait qu'ils sont susceptibles de provoquer le cancer et des anomalies congénitales ou d'autres effets néfastes sur la reproduction. Pour plus d'informations https://www.p65warnings.ca.gov/