Skip to Content
BambuLab Voron
  1. All Products
  2. P1P-P1S
  3. Full Kit BambuLab P1P-P1S, Starlex DHB D3.0x24 HSSC, 2x30W
Special Kit Offer
Full Kit BambuLab P1P-P1S, Starlex DHB D3.0x24 HSSC, 2x30W

Full Kit BambuLab P1P-P1S, Starlex DHB D3.0x24 HSSC, 2x30W

https://www.swiss3dc.com/web/image/product.template/871/image_1920?unique=9d2d68f

Enjoy the quick nozzle swap in seconds without removing any screw or connector, tool free.


Drop In Replacement.


Included: 

1x Heat Sink to keep same nozzle height as original

1x HSC 24

1x Base Plate mini D4

1x Base Heat Set (2x HB D3.0x24, 2x HB Clamp24, 1x Clip 3.0, 1x Sock)

2x MCH 30W 24V Heaters P series connector

1x Thermistor NTC 100K 3950 P series connector

4x HSS+C Nozzles (0.2/0.4/0.6/0.8mm)


Due to the reduced thermal efficiency of full steel nozzles, hardened stainless steel nozzles will necessitate a minor temperature boost. It is suggested to increase the temperature by 5 to 10°C to ensure the standard flow rate is achieved.


When changing nozzles, the basic calibration is recommended.

This unit is equipped with two MCH heating elements, each delivering 30W of power, ensuring outstanding heating efficiency that works seamlessly with the heating board.


116.10 CHF 116.1 CHF 129.00 CHF Tax Excluded

129.00 CHF Tax Excluded

Not Available For Sale

This combination does not exist.

Contact Us


Terms and Conditions
14 days return, money-back guarantee
Shipping: 2-7 Busin​ess Days​

Starlex DHB is a game changer for tool free nozzle swap in seconds.

No material leak as the extremity is located into the cold section, in the heat sink.

Experience exceptional thermal efficiency with the innovative dual heat block DHB eco-system.

Opt for standard or protruded nozzles to maximise your flow and elevate your performance.

Drop in replacement, same nozzle height

1.75mm filament

When it comes to 3D printing, the choice of nozzle can significantly impact your results.

The best compromise:

3.0mm nozzles, typically made from brass and copper, excel in thermal conductivity but may lack the abrasion resistance needed for more demanding materials. They are ideal for use with filaments like PLA and PETG.

3.0mm nozzles, Hardened stainless steel nozzles with a copper sleeve (HSSC) provide seamless compatibility with brass nozzles, both featuring a 3.0mm body diameter, allowing for effortless interchangeability. This versatility is a game-changer for any serious 3D printing enthusiast.

With a 3.0mm body diameter, these nozzles require corresponding heat blocks to be 3mm as well, ensuring optimal performance. Choosing the right pairing is essential.

------------------------

2.5mm nozzles (HSS) made from hardened stainless steel are an exceptional option. These nozzles are meticulously crafted to endure the challenges posed by abrasive filaments and high-temperature environments, ensuring reliability and performance.

The 2.5mm body diameter is not just a number; it is a carefully considered design that reduces the thermal barrier, optimising heat transfer despite the metal's lower thermal conductivity.

For those seeking consistent flow rates, a slight increase in the standard temperature by 5 to 10°C may be necessary with full hardened stainless steel nozzles, even a little more depending on the filament quality. This minor adjustment can make a significant difference in your printing outcomes.

It's important to note that while certain abrasive filaments can wear down hardened nozzles over time, the investment in high-quality stainless steel pays off in durability and performance.


Complete the Hot-end with the adapted parts below